You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
103 lines
3.0 KiB
103 lines
3.0 KiB
5 years ago
|
/*
|
||
|
|
DHCP Chat Server
|
||
|
|
|
||
|
|
A simple server that distributes any incoming messages to all
|
||
|
|
connected clients. To use, telnet to your device's IP address and type.
|
||
|
|
You can see the client's input in the serial monitor as well.
|
||
|
|
Using an Arduino Wiznet Ethernet shield.
|
||
|
|
|
||
|
|
THis version attempts to get an IP address using DHCP
|
||
|
|
|
||
|
|
Circuit:
|
||
|
|
* Ethernet shield attached to pins 10, 11, 12, 13
|
||
|
|
|
||
|
|
created 21 May 2011
|
||
|
|
modified 9 Apr 2012
|
||
|
|
by Tom Igoe
|
||
|
|
modified 02 Sept 2015
|
||
|
|
by Arturo Guadalupi
|
||
|
|
Based on ChatServer example by David A. Mellis
|
||
|
|
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <SPI.h>
|
||
|
|
#include <Ethernet.h>
|
||
|
|
|
||
|
|
// Enter a MAC address and IP address for your controller below.
|
||
|
|
// The IP address will be dependent on your local network.
|
||
|
|
// gateway and subnet are optional:
|
||
|
|
byte mac[] = {
|
||
|
|
0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x02
|
||
|
|
};
|
||
|
|
IPAddress ip(192, 168, 1, 177);
|
||
|
|
IPAddress myDns(192, 168, 1, 1);
|
||
|
|
IPAddress gateway(192, 168, 1, 1);
|
||
|
|
IPAddress subnet(255, 255, 0, 0);
|
||
|
|
|
||
|
|
// telnet defaults to port 23
|
||
|
|
EthernetServer server(23);
|
||
|
|
boolean gotAMessage = false; // whether or not you got a message from the client yet
|
||
|
|
|
||
|
|
void setup() {
|
||
|
|
// You can use Ethernet.init(pin) to configure the CS pin
|
||
|
|
//Ethernet.init(10); // Most Arduino shields
|
||
|
|
//Ethernet.init(5); // MKR ETH shield
|
||
|
|
//Ethernet.init(0); // Teensy 2.0
|
||
|
|
//Ethernet.init(20); // Teensy++ 2.0
|
||
|
|
//Ethernet.init(15); // ESP8266 with Adafruit Featherwing Ethernet
|
||
|
|
//Ethernet.init(33); // ESP32 with Adafruit Featherwing Ethernet
|
||
|
|
|
||
|
|
// Open serial communications and wait for port to open:
|
||
|
|
Serial.begin(9600);
|
||
|
|
while (!Serial) {
|
||
|
|
; // wait for serial port to connect. Needed for native USB port only
|
||
|
|
}
|
||
|
|
|
||
|
|
// start the Ethernet connection:
|
||
|
|
Serial.println("Trying to get an IP address using DHCP");
|
||
|
|
if (Ethernet.begin(mac) == 0) {
|
||
|
|
Serial.println("Failed to configure Ethernet using DHCP");
|
||
|
|
// Check for Ethernet hardware present
|
||
|
|
if (Ethernet.hardwareStatus() == EthernetNoHardware) {
|
||
|
|
Serial.println("Ethernet shield was not found. Sorry, can't run without hardware. :(");
|
||
|
|
while (true) {
|
||
|
|
delay(1); // do nothing, no point running without Ethernet hardware
|
||
|
|
}
|
||
|
|
}
|
||
|
|
if (Ethernet.linkStatus() == LinkOFF) {
|
||
|
|
Serial.println("Ethernet cable is not connected.");
|
||
|
|
}
|
||
|
|
// initialize the Ethernet device not using DHCP:
|
||
|
|
Ethernet.begin(mac, ip, myDns, gateway, subnet);
|
||
|
|
}
|
||
|
|
// print your local IP address:
|
||
|
|
Serial.print("My IP address: ");
|
||
|
|
Serial.println(Ethernet.localIP());
|
||
|
|
|
||
|
|
// start listening for clients
|
||
|
|
server.begin();
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop() {
|
||
|
|
// wait for a new client:
|
||
|
|
EthernetClient client = server.available();
|
||
|
|
|
||
|
|
// when the client sends the first byte, say hello:
|
||
|
|
if (client) {
|
||
|
|
if (!gotAMessage) {
|
||
|
|
Serial.println("We have a new client");
|
||
|
|
client.println("Hello, client!");
|
||
|
|
gotAMessage = true;
|
||
|
|
}
|
||
|
|
|
||
|
|
// read the bytes incoming from the client:
|
||
|
|
char thisChar = client.read();
|
||
|
|
// echo the bytes back to the client:
|
||
|
|
server.write(thisChar);
|
||
|
|
// echo the bytes to the server as well:
|
||
|
|
Serial.print(thisChar);
|
||
|
|
Ethernet.maintain();
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|