You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
95 lines
3.4 KiB
95 lines
3.4 KiB
5 years ago
|
/*==============================================================================
|
||
|
|
* NETWORK CONFIGURATION
|
||
|
|
*
|
||
|
|
* You must configure your particular hardware. Follow the steps below.
|
||
|
|
*
|
||
|
|
* By default, StandardFirmataEthernet is configured as a TCP client.
|
||
|
|
* To configure as a TCP server, see STEP 2
|
||
|
|
*============================================================================*/
|
||
|
|
|
||
|
|
// STEP 1 [REQUIRED]
|
||
|
|
// Uncomment / comment the appropriate set of includes for your hardware (OPTION A or B)
|
||
|
|
// Option A is enabled by default.
|
||
|
|
|
||
|
|
/*
|
||
|
|
* OPTION A: Configure for Arduino Ethernet board or Arduino Ethernet shield (or clone)
|
||
|
|
*
|
||
|
|
* To configure StandardFirmataEthernet to use the original WIZ5100-based
|
||
|
|
* ethernet shield or Arduino Ethernet uncomment the WIZ5100_ETHERNET define below
|
||
|
|
*/
|
||
|
|
#define WIZ5100_ETHERNET
|
||
|
|
|
||
|
|
#ifdef WIZ5100_ETHERNET
|
||
|
|
#include <SPI.h>
|
||
|
|
#include <Ethernet.h>
|
||
|
|
EthernetClient client;
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/*
|
||
|
|
* OPTION B: Configure for Arduin Yun
|
||
|
|
*
|
||
|
|
* The Ethernet port on the Arduino Yun board can be used with Firmata in this configuration.
|
||
|
|
*
|
||
|
|
* To execute StandardFirmataEthernet on Yun uncomment the YUN_ETHERNET define below and make
|
||
|
|
* sure the WIZ5100_ETHERNET define (above) is commented out.
|
||
|
|
*
|
||
|
|
* On Yun there's no need to configure local_ip and mac address as this is automatically
|
||
|
|
* configured on the linux-side of Yun.
|
||
|
|
*
|
||
|
|
* Note that it may take several seconds to establish a connection with the Yun.
|
||
|
|
*/
|
||
|
|
//#define YUN_ETHERNET
|
||
|
|
|
||
|
|
#ifdef YUN_ETHERNET
|
||
|
|
#include <Bridge.h>
|
||
|
|
#include <YunClient.h>
|
||
|
|
YunClient client;
|
||
|
|
#endif
|
||
|
|
|
||
|
|
// STEP 2 [REQUIRED for all boards and shields]
|
||
|
|
// TCP Client configuration:
|
||
|
|
// To configure your board as a TCP client, set the IP address of the server you want to connect to.
|
||
|
|
// TCP Server configuration:
|
||
|
|
// To configure your board as a TCP server, comment out the following line and also ensure that
|
||
|
|
// remote_host is also commented out.
|
||
|
|
#define remote_ip IPAddress(10, 0, 0, 3)
|
||
|
|
// *** REMOTE HOST IS NOT YET WORKING ***
|
||
|
|
// replace with hostname of server you want to connect to, comment out if using 'remote_ip'
|
||
|
|
// #define remote_host "server.local"
|
||
|
|
|
||
|
|
// STEP 3 [REQUIRED]
|
||
|
|
// Replace with the port that your client or server is listening on.
|
||
|
|
#define network_port 3030
|
||
|
|
|
||
|
|
// STEP 4 [REQUIRED unless using DHCP]
|
||
|
|
// Replace with your board or ethernet shield's IP address
|
||
|
|
// Comment out if you want to use DHCP
|
||
|
|
#define local_ip IPAddress(10, 0, 0, 15)
|
||
|
|
|
||
|
|
// STEP 5 [REQUIRED]
|
||
|
|
// replace with ethernet shield mac. Must be unique for your network
|
||
|
|
const byte mac[] = {0x90, 0xA2, 0xDA, 0x00, 0x53, 0xE5};
|
||
|
|
|
||
|
|
/*==============================================================================
|
||
|
|
* CONFIGURATION ERROR CHECK (don't change anything here)
|
||
|
|
*============================================================================*/
|
||
|
|
|
||
|
|
#if !defined WIZ5100_ETHERNET && !defined YUN_ETHERNET
|
||
|
|
#error "you must define either WIZ5100_ETHERNET or YUN_ETHERNET in ethernetConfig.h"
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#if defined remote_ip && defined remote_host
|
||
|
|
#error "cannot define both remote_ip and remote_host at the same time in ethernetConfig.h"
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/*==============================================================================
|
||
|
|
* PIN IGNORE MACROS (don't change anything here)
|
||
|
|
*============================================================================*/
|
||
|
|
|
||
|
|
#if defined(WIZ5100_ETHERNET)
|
||
|
|
|
||
|
|
// ignore SPI pins, pin 10 (Ethernet SS) and pin 4 (SS for SD-Card on Ethernet shield)
|
||
|
|
#define IS_IGNORE_PIN(p) ((IS_PIN_SPI(p) || (p) == 4) || (p) == 10)
|
||
|
|
|
||
|
|
#endif
|