You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
96 lines
2.5 KiB
96 lines
2.5 KiB
5 years ago
|
/*
|
||
|
|
DHCP-based IP printer
|
||
|
|
|
||
|
|
This sketch uses the DHCP extensions to the Ethernet library
|
||
|
|
to get an IP address via DHCP and print the address obtained.
|
||
|
|
using an Arduino Wiznet Ethernet shield.
|
||
|
|
|
||
|
|
Circuit:
|
||
|
|
Ethernet shield attached to pins 10, 11, 12, 13
|
||
|
|
|
||
|
|
created 12 April 2011
|
||
|
|
modified 9 Apr 2012
|
||
|
|
by Tom Igoe
|
||
|
|
modified 02 Sept 2015
|
||
|
|
by Arturo Guadalupi
|
||
|
|
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <SPI.h>
|
||
|
|
#include <Ethernet.h>
|
||
|
|
|
||
|
|
// Enter a MAC address for your controller below.
|
||
|
|
// Newer Ethernet shields have a MAC address printed on a sticker on the shield
|
||
|
|
byte mac[] = {
|
||
|
|
0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x02
|
||
|
|
};
|
||
|
|
|
||
|
|
void setup() {
|
||
|
|
// You can use Ethernet.init(pin) to configure the CS pin
|
||
|
|
//Ethernet.init(10); // Most Arduino shields
|
||
|
|
//Ethernet.init(5); // MKR ETH shield
|
||
|
|
//Ethernet.init(0); // Teensy 2.0
|
||
|
|
//Ethernet.init(20); // Teensy++ 2.0
|
||
|
|
//Ethernet.init(15); // ESP8266 with Adafruit Featherwing Ethernet
|
||
|
|
//Ethernet.init(33); // ESP32 with Adafruit Featherwing Ethernet
|
||
|
|
|
||
|
|
// Open serial communications and wait for port to open:
|
||
|
|
Serial.begin(9600);
|
||
|
|
while (!Serial) {
|
||
|
|
; // wait for serial port to connect. Needed for native USB port only
|
||
|
|
}
|
||
|
|
|
||
|
|
// start the Ethernet connection:
|
||
|
|
Serial.println("Initialize Ethernet with DHCP:");
|
||
|
|
if (Ethernet.begin(mac) == 0) {
|
||
|
|
Serial.println("Failed to configure Ethernet using DHCP");
|
||
|
|
if (Ethernet.hardwareStatus() == EthernetNoHardware) {
|
||
|
|
Serial.println("Ethernet shield was not found. Sorry, can't run without hardware. :(");
|
||
|
|
} else if (Ethernet.linkStatus() == LinkOFF) {
|
||
|
|
Serial.println("Ethernet cable is not connected.");
|
||
|
|
}
|
||
|
|
// no point in carrying on, so do nothing forevermore:
|
||
|
|
while (true) {
|
||
|
|
delay(1);
|
||
|
|
}
|
||
|
|
}
|
||
|
|
// print your local IP address:
|
||
|
|
Serial.print("My IP address: ");
|
||
|
|
Serial.println(Ethernet.localIP());
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop() {
|
||
|
|
switch (Ethernet.maintain()) {
|
||
|
|
case 1:
|
||
|
|
//renewed fail
|
||
|
|
Serial.println("Error: renewed fail");
|
||
|
|
break;
|
||
|
|
|
||
|
|
case 2:
|
||
|
|
//renewed success
|
||
|
|
Serial.println("Renewed success");
|
||
|
|
//print your local IP address:
|
||
|
|
Serial.print("My IP address: ");
|
||
|
|
Serial.println(Ethernet.localIP());
|
||
|
|
break;
|
||
|
|
|
||
|
|
case 3:
|
||
|
|
//rebind fail
|
||
|
|
Serial.println("Error: rebind fail");
|
||
|
|
break;
|
||
|
|
|
||
|
|
case 4:
|
||
|
|
//rebind success
|
||
|
|
Serial.println("Rebind success");
|
||
|
|
//print your local IP address:
|
||
|
|
Serial.print("My IP address: ");
|
||
|
|
Serial.println(Ethernet.localIP());
|
||
|
|
break;
|
||
|
|
|
||
|
|
default:
|
||
|
|
//nothing happened
|
||
|
|
break;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|